-
Nullifire FJ260 Cavity Barrier
£77.81FJ260 Cavity Barrier is a close state cavity barrier made of rock mineral wool and designed to maintain the required fire resistance when following fire compartment lines.
-
Nullifire FJ400 Intuspan
£16.20A very pliable intumescent expansion joint with a high level of movement that is suitable for gaps up to 100 mm, providing up to 2 hours fire performance with no adhesive required in most situations.
Ideal for high vibration areas, such as lift shaft interfaces
Can accommodate regular cycles of high or low amplitude movement
Tolerates very large movements
Unaffected by moisture
Easy to install using finger pressure even in uneven gaps
Suits vertical & horizontal joints, and head of walls
Full dry systemPlease note: Selected items are Made To Order subject to a MOQ and an extended lead time – please see below
-
Nullifire FO230/FO323 Slotted Steel Angles & Straps
£26.12For securing fire barriers above partition walls in fire stopping applications.
Made from DX51D+Z275 NAC galvanised steel
20 x 6mm slotted holes @ 300mm Ctrs in centre on both sides of angle and centre of strap.
Meets relevant British Standards – see description below for more detailsPlease note – Selected items are Made To Order subject to an MOQ and an extended lead time see ‘Order References’ below
-
Nullifire FP170 Intucollar Intumescent Pipe Collars
£11.33Expands when exposed to fire, reinstating the fire performance of compartment walls and floors which have been penetrated by combustible pipes.
Up to 4 hours fire resistance – Tested to EN 1366-3
Tested with combustible pipes (PVC, PE, PP, SanPVC, Bevex, etc.), insulated non- combustible pipes (steel) and network cable bundles (up to 125 mm)
Flexible walls (stud partitions) or rigid walls (masonry, concrete) of 100 mm minimum thickness. Rigid (concrete) floors of 150 mm minimum thickness
Easy to install, stainless steel shell
Water resistant and non-corrosive: inert product
This new, improved version of FP170 is available in multiple sizes; other sizes are available to order by special request – contact our sales team on 0113 2455450 (option 2) or send a message to technical@rawlinspaints.com for more information. -
Nullifire FP220 Service Sleeve
£30.55A pipe closer device, comprising of an intumescent material within a stainless steel shell.
Expands when exposed to fire, reinstating the fire performance of compartment walls which have been penetrated by combustable pipes
Suitable for retrofit or inclusion prior to service installation, PE, HDPE, ABS, San+PVC, PP, PVC-C, UPONOR, DB, MLCP pipes
Up to 120 minutes fire protectionFP220 is required to be installed within a suitably tested substrate or included within other Nullifire tested system solutions.
Please note: Selected items are Made To Order subject to a MOQ and an extended lead time – please see below -
Nullifire FP302 Intustrap/Band
£251.02A rubber based product with graphite impregnation that creates an extremely flexible pipe closure device. The product remains dormant, until exposed to fire conditions, at which point it will expand to fill the space left by the melting combustible element. FP302 has a release tape to one side. This permits the thermal expansion of services, if required, and eases its application, allowing the product to slide freely along the pipe to its end location.
Up to 4 hours fire resistance – Tested to BS EN 1366-3 and BS 476 Pt 20-22
Suitable for use in many substrate types
Remains permanently flexible
Unaffected by moisture
Easy to inspect
CE marked
Simply link with duct tape -
Nullifire FP333 Trunking Infill
Price range: £4.34 through £10.22FP333 Trunking Infill is a fire resistant compressible foam strip layered with high expansion intumescent material produced in three sizes. In a fire, the intumescent expands and hardens providing a fire and cold smoke barrier.
-
Nullifire FR230 Intucompound Fire Mortar
£30.94Gypsum based mortar used to reinstate the fire resistance performance of floor & wall constructions where they have been breached with apertures for the penetration of single or multiple services.
Up to 4 hours fire resistance – Tested to EN 1366-3 & 4
Provides a safe working platform for loads up to 2.5 kN/m²
1.21 m² without framework requirement
Load and impact capability after 50 hours only
Flows easily around and behind services
Rapid setting, zero shrinkage formulation
Can be used as pourable or trowel grade
Acoustic and thermal performance
Features Optifire+, a unique pigment technology, visible only with a specific Nullifire detector ; Optifire+ offers lifetime identification, and remains traceable even after a fire. -
Nullifire FS702 Intumastic Fire Resistant Acrylic Sealant
£42.26FS702 Intumastic is a water-based acrylic sealant which cures to give a firm but flexible fire seal, for both linear joints & service penetrations.
-
Nullifire FS703 Fire Resistant Silicone Sealant
£126.98FS703 is a low modulus, neutral cure, silicone sealant, suitable for linear gaps sealing in order to reinstate the fire performance in compartment walls & floors.
-
Nullifire FS709 Intumastic HP Intumescent Sealant
£232.39A heat-reactive, intumescent acrylic fire barrier mastic for internal use around services in walls and floors.
Seals around pipes, cables and cable trays.
Provides up to 4 hours of fire resistance.
60 to 120 min tack time (depending on temperature/humidity). -
Nullifire FS712 Intucoat Brush Grade
£50.70Water-based acrylic coating and adhesive, which may be used in conjunction with FB750 Intubatt, FB770 Intudeck and FJ220 Intubatt 3 as a bonding agent and a surface repair coating.
Up to 4 hours fire resistance – Tested to EN 1366-4, EN 1366-3 and BS 476 Pt 20-22 in conjunction with FB750 Intubatt, FB770 Intudeck and FJ220 Intubatt 3
Used for sealing FB750 Intubatt/FB770 Intudeck/FJ220 Intubatt 3 on flexible walls, rigid walls & floors (usage dependent on product selected)
Acoustics up to 59 dB – Air seal up to 2,000 Pa
Provides a tested smoke seal
Optifire unique traceability identifiers -
Nullifire PM020 Alkyd High-Build Primer
£74.39Fast-drying steel primer that provides corrosion protection on structural steel. Well suited for fabrication shops that need fast cure to dry and handle times.
Rapid cure and fast-drying
VOC compliant for most areas
Good for filling properties on rough and pitted steelNullifire have made the decision in March 2023 to rebrand Nullifire PM020 High Build Alkyd Primer as Carboline Carbocoat 115 – please see a letter explaining the changes HERE.
-
Nullifire PR102 PE Joint Backer Rods
£97.10Used to control sealant depth in sealant joints, avoiding 3-sided adhesion.
Available in white.Important!
Selected items are Made To Order subject to a MOQ and an extended lead time – see ‘Size Reference’ below
-
Nullifire SC601 On Site & Off-Site Intumescent Base Coat
£334.02Single pack acrylic thin film intumescent basecoat for fire protection of internal & semi-exposed structural steelwork up to 60 minutes.
This product is optimised to provide 60 minutes fire resistance to ‘I’ section beams and columns, hollow columns and beams, as well as cellular beams, concrete filled hollows and solid steel rods. Limited 90 minute protection is also available. SC601 can be used on steel, cast iron and galvanised steel.Intumescent paint for steel
Easy to apply, designed for on-site or off-site application by airless spray
Fast drying (compared to water based products in cold or humid conditions) for a quick turn around & shorter sites times for contractors – touch dry in 30 mins, recoat after 4 hours (at 20°C)
Competitive loadings – compatible with various primers & topcoats
Optifire+ unique traceability identifier -
Nullifire SC801 On-Site Water-Based Intumescent Basecoat
£235.13Nullifire SC801 On-Site Water-Based Intumescent Basecoat is a water-based, white, thin film intumescent coating for the protection of internal structural steelwork, providing up to 120 minutes fire resistance.
Please Note: We strongly recommend Tricomb Plastic Wet Film Gauges are used to help ensure correct film thicknesses are achieved during application
More Information Delivery Info -
Nullifire SC804 On-Site Water-Based Intumescent Basecoat
£233.22A water based intumescent coating used for internal structural steel to C1 and C2 environments that can be top coated with a suitable topcoat for decorative and durability purposes.
Includes Optifire+ technology – reliable and traceable fire protection
Developed to give optimised loadings for up to 90 minutes
Up to 120 minutes fire resistance
Ultra Low VOC
Compatible with a wide range of primers and topcoats
Excellent aesthetics
Supplied ready to use
Loading Tables available to download -
Nullifire SC900 On-Site Intumescent Steel Coating Repair Kit
£128.51Enables seamless repairs to accidental damage in isolated areas in order to preserve fire integrity, such as long-term repairs to accidental damage caused to an SC901 or SC902 coating.
Up to 120 minutes fire resistance
Can be applied to a smooth matt finish
A compatible top seal can be applied if a decorative finish is required
Maintains the integrity of the original coating even after the repair
Same fast cure properties as the original material
Repairs can be done at low temperatures and are weather resistant
Suitable for treating scratches, grazes, indentations and minor abrasions
Low VOC and no solvent entrapment or prolonged solvent odourPlease Note: This Product Is Made to Order Subject to a 23 Working Day Lead time and a MOQ of 20
More Information Delivery Info -
Nullifire TS134 – Acrylic Polyurethane Topcoat (High Gloss)
£106.74A two-component, high-gloss, and high-solid polyurethane topcoat in 350+ colours, which can be easily sprayed with conventional as well as airless equipment. The coating has excellent flow and application properties which provides a smooth, durable, and easy to clean surface.
Please note: Colours are Made To Order subject to a MOQ of 80 units and an extended lead time of 10 working daysReplaces Nullifire TS134 Acrylic Polyurethane Top Seal
Excellent weatherability
Excellent flexibility
Excellent abrasion resistance
Easy application with airless and conventional equipment
Suitable for plural component and electrostatic spray
VOC compliant to current AIM regulationsPlease note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.
Professional use only – from the 24th August 2023, adequate training is required before industrial or professional use of this product.
Should you require training, visit – https://www.safeusediisocyanates.eu/
Coverage Calculator More Information Delivery Info -
Nullifire TS815 Solvent-Based Acrylic Topcoat
£113.30Nullifire TS815 Solvent-Based Acrylic Top Seal is a single pack, high build modified acrylic topseal conforming to 2010 VOC limits. This product is designed for use with the Nullifire System S range of intumescent basecoats.
Available in 4,300+ colours, inc. RAL, RAL Design, BS, NCS & the new NCS 2050 colours
-
Nullifire TS816 Water-Based Acrylic Topcoat
£118.91TS816 is a waterborne, acrylic eggshell decorative topcoat. It is primarily for use with Nullifire intumescent steel coatings.
